Terabase Energy released a new version of Construct, its construction software for utility-scale solar, storage and wind projects, on November 16, 2026. The Berkeley company added an AI agent that answers questions about the site in plain language and builds reports, along with small magnetic beacons that track equipment across the job. The release affects the daily progress report and the QC walk on solar sites that EPCs build and owners oversee.
What it does
On a large solar job, progress is often pieced together from daily reports and spreadsheets, Terabase says, and a single 300 MW site can cover 1,500 to 2,500 acres. Construct captures progress and quality data on site. Once installation starts, a drone-in-a-box fleet flies the site every day. Crews log inspections in a mobile QC app, and the beacons report the location, idle time and utilization of anything they are stuck to, from pile drivers to portable toilets.
Everything lands in a digital twin, which here means a GIS map of the plant where each pile, module, inverter and MV foundation is its own record with a status and a history. Construct compares what was built against the design and flags deviations. The release’s example is a misrouted MV feeder trench caught before it was backfilled. Infrared drone flights and robotic array inspections flag defects automatically and pin each one to the element in the twin.
“On a solar site, the cost of a problem depends on when you find it,” said Pierre Gousseland, Terabase’s senior vice president of product and a co-founder.
The agent sits on top of that data. A superintendent or field engineer types a request, and the agent answers it, flags deviations from plan, builds a custom report or sets up a view such as a comparison of two drone flights or a filtered list of open QC items. A forecasting view gives the daily install rate needed to hold the finish date, and the product page lists a Primavera P6 integration for plan-versus-actual tracking.
Energy Intelligence applies later in the job, starting with the first energized MV circuit. It uses PlantPredict, Terabase’s energy model, to calculate what the as-built plant should produce and compares that with measured output, loss by loss, down to the tracker. The same model sets the baseline for the Capacity Test.
On the EPC side, the users are superintendents and field engineers for progress and QC, project controls staff for the schedule, and the equipment manager deciding when a rental can go off-rent. An owner’s team sees every project marked green or red against plan and receives the digital twin at handover as a record of the build.
Evidence so far
The evidence so far is Terabase’s announcement, with comments from MasTec and Doral Renewables, and an April 2026 Terabase release about EDP Renewables.
These claims come from Terabase and its customers:
- Construct has been used on more than 35 GW of solar, storage and wind projects. In April, Terabase put the figure at more than 25 GW.
- Terabase’s drone fleet flies more than 3 GW of active construction every day.
- Joshua Hauger, director of construction at MasTec, said Construct gives MasTec’s field teams and leadership real-time visibility into project performance and helps them find constraints earlier.
- Amit Nadkarni, COO at Doral Renewables, said a single portfolio view lets the company manage more projects without adding layers of reporting.
- In April, EDP Renewables had managed more than 2 GW of solar projects with Construct. Kent Shields, its executive vice president of engineering and construction in North America, said the platform had produced cost and time savings by surfacing issues earlier.
The customer comments describe Construct as a whole and do not separate out the new agent or the beacons. Figures on how much earlier defects are found, or on hours of reporting saved, are not yet public.
How to measure it on your projects
Track defect detection lag: the number of calendar days between the day an element was installed and the day a defect on it was logged. Terabase’s case for daily flights and automated QC is that defects get found sooner, so this is the number a pilot should move.
Capture the baseline from a completed solar job before the pilot:
- Export the QC log or punch list, with the date each defect was logged and the block or row it was on.
- Match each defect to its install date from the daily reports or the installation tracker.
- Compute the median lag, and count how many defects were found at or after mechanical completion.
On the pilot, log the same figures from Construct’s QC list. Record how many flagged deviations your field engineers confirmed in the field and how many they rejected, to see what share of the flagged items hold up on inspection.
A first step on one job is to pull 20 defects from a recent block and match each to its install date.
Availability and cost
Terabase will demonstrate the new version at RE+ 2026 in Las Vegas, November 17 to 19, at booth C6682. The QC app runs on Apple and Android devices. Construct’s product page lists no prices and directs buyers to a demo request.
Related reading: MasTec will use Gritt’s robotic solar panel installers on its utility-scale jobs.